Fukushima begins fuel rod removal

November 18, 2013
By
Deeter Does Wirless

This handout picture taken by Tokyo Electric Power Co (Tepco) on 14 November 2013 shows an operation using imitation fuel rods during an exercise to remove fuel rods from a pool at the unit four reactor building of Tepco's Fukushima Dai-ichi nuclear plant in the town of Okuma in Fukushima prefectureTepco has been preparing for months to remove fuel rods at Fukushima

Workers at Japan’s stricken Fukushima nuclear plant have begun removing fuel rods from a storage pond at the Unit 4 reactor building.

The delicate operation is seen as a necessary step in stabilising the site.

It will take about two days to remove the first 22 fuel rod assemblies, plant operator Tepco says.

Overall, more than 1,500 assemblies must be removed in what correspondents describe as a risky and dangerous operation set to take a year.

Experts say hydrogen explosions after the earthquake and tsunami in March 2011 have made the current storage facility vulnerable to further tremors.

The fuel rod assemblies are four-meter long tubes containing pellets of uranium fuel, and the fear is that some may have been damaged during the disaster.

When the tsunami struck, water knocked out cooling systems to three of Fukushima’s reactors, which went into a state of partial meltdown.

Unit 4 was undergoing maintenance, so all of its fuel rods were being stored. But a build-up of hydrogen triggered an explosion in Unit 4, damaging its structure.

‘Important process’

The removal process, which has been preceded by months of repair work and planning, began on Monday afternoon.

“At 15:18 [06:18 GMT], we started to pull up the first fuel assembly with a crane,” a spokesman for Tepco (Tokyo Electric Power Company) said.

A recently installed crane is being lowered into the pool and hooked on to the assemblies to place them inside a cask.

This handout picture taken by Tokyo Electric Power Co (Tepco) on 14 November  2013 shows an operation using imitation fuel rods during an exercise to remove the fuel rods from a pool at the unit four reactor building of Tepco's Fukushima Dai-ichi nuclear plant in the town of Okuma in Fukushima prefectureRemoval of fuel rods from the storage pond is a key step in the decommissioning

This handout picture taken by Tokyo Electric Power Co (Tepco) on 13 November 2013 shows a cask of nuclear fuel being lifted and moved by Tepco workers during an exercise to remove fuel rods from a pool at the unit four reactor building of Tepco's Fukushima Dai-ichi nuclear plant in the town of Okuma in Fukushima prefecture Tepco has conducted trial runs of the process, which involves large casks

The fuel rods will then be deposited into a more secure storage pool with a cooling system.

Experts say it is vital that the casks are watertight so the rods have no contact with air – which risks overheating and possible contamination.

Yoshihide Suga, Japan’s top government spokesman, said he hoped the operation would go as planned.

“We hope that this [process] will be conducted in a manner that will not disturb local residents, and that the removal will be done on schedule, properly and safely,” he said.

Tepco spokesman Masayuki Ono called the operation “a very important process in moving ahead with the plant’s decommissioning”.

Nuclear Regulation Authority Chairman Shunichi Tanaka has warned that rubble from the blast in the pool could pose a problem, Kyodo news agency reported.

“The fuel has to be handled very carefully. There is a need to make sure that a fuel assembly is not pulled out (from the fuel rack) by force when it gets stuck because of the rubble,” Kyodo news agency quoted him as saying.

The Fukushima nuclear power plant has suffered a number of setbacks in recent months, including a series of toxic water leaks and worker errors.

Graphic: Removing rods from reactor 4 at Fukushima

  • 1. Small crane retrieves spent fuel rods from storage pool. A protective shell has been built over the top of the damaged reactor building. There are 1,331 spent fuel rods and 202 unused fuel rods to be removed
  • 2. Fuel rods are carefully lowered into specially-constructed casks, which each weigh 91 tonnes and can hold up to 22 rods
  • 3. A larger crane lifts full cask out of the storage pond and lowers it out of the building and on to a flat-bed truck. The casks will then be taken to a safe storage pool on the Fukushima site
Deeter Does Wirless

Article source: http://www.bbc.co.uk/news/world-asia-24958048#sa-ns_mchannel=rss&ns_source=PublicRSS20-sa The feed :

Tags:

Sponsored By:

The Deeter Group

Deeter Electronics Ltd. | Deeter Electronics Inc | Deeter Group Asia | Deeter Group Germany | Deeter Group Corporate

Head & Registered Office:
Deeter Electronics Ltd.
Deeter House,
Valley Road,
Hughenden Valley,
Bucks. HP14 4LW

Tel: +44 (0) 1494 566 046
Fax: +44 (0) 1494 563 961
E-mail: [email protected]


The Deeter Group with products ranging from: , , , continuous , 4-20mA , , , , , , , a , wireless sensor and much more.

If you want a standard or a custom level switch, float switch, level sensor, or wireless sensor, contact us via email [email protected] or call us now on 01494 566 046.

Company Name: The Deeter Group

Location: Hughenden Valley, UK

Deeter Electronics USA
Deeter Electronics USA
Wireless sensor system | Radio telemetry | Level switches | Level sensors | Liquid level sensor | Float switches | Controllers & indicators | Industrial weighing equipment | Electronic circuit design & manufacture | Software design | Reed relays | Ultrasonic level flow sludge & proximity sensors | Proximity sensors & switches | Reed switches | Litz wire | Wago Terminals | Mechanical & magnetic floats | Boiler control |

Deeter Electronics UK
Wireless sensor system | Radio telemetry | Level switches | Level sensors | Liquid level sensor | Float switches | Controllers & indicators | Industrial weighing equipment | Electronic circuit design & manufacture | Software design | Reed relays | Ultrasonic level flow sludge & proximity sensors | Proximity sensors & switches | Reed switches | Litz wire | Wago Terminals | Mechanical & magnetic floats | Boiler control |

Deeter Electronics Europe
Wireless sensor system | Radio telemetry | Level switches | Level sensors | Liquid level sensor | Float switches | Controllers & indicators | Industrial weighing equipment | Electronic circuit design & manufacture | Software design | Ultrasonic level flow sludge & proximity sensors | Proximity sensors & switches | Reed switches | Litz wire | Wago Terminals | Mechanical & magnetic floats | Boiler control |

Sensor Magazine Websites
Explosion Proof Sensors UK | Explosion Proof Sensors | Water Level Measurement | Liquid Level Sensing | Liquid Level Measurement | Liquid Level Sensors UK | Liquid Level Sensors Europe | Wireless Sensors | Sensor Magazine | Industrial Sensors



Water use